Rated power 90w and Maximum power 100w. 3.15 (80mm) ± 2mm. Maximum working current is 29mA. The running current must be kept below 27mA.
The life span can reach 8,000 hours if the current is kept below 25mA. We will send a new one freely if the tube is broken during transit.
Once received the laser tube, please check again at the first time. We need the damaged record from the courier as the proof before we send the new one free. Laser spot with depth of 5mm. Reci W2 CO2 laser tube is suitable for laser marking, laser cutting and laser engraving which are the ideal choice of laser paper - cut, laser cloth cutting and marble marking. Cutting function Engraving function: Very good, when the working current is 4mA and the tube is in the state of preionization, the laser can be used for high-frequency impulse engraving.
As long as the length parameter is applicable, you can use our tube to substitute! Appearance: The tube is sealed by metal material.
No metal material is used by other manufacturers. Their tubes are handmade and need extra water cooling for front and rare mirrors.
Tube frame: This is exclusive design for Reci laser tube. This frame is shockproof and makes sure the tube will not move during the transport. No frame is provided by other manufacturers. Length: The length is only 1.2m.The length of other 80w tubes is 1.64m. 300mm must be projecting in the machine. That costs more for machine panel, package and transport. How to identify a good or bad laser tube?
1Install the laser tube properly; 2Prepare a piece of acrylic board; 3Put the acrylic board on the light outlet of the laser tube for laser dot test; 4If it can form a standard conical hole (it proofs the standard TEMOO Basement Membrane Mode was applied), it means the laser tube is qualified. Then you can use it without any worry. Water cooling: Using purified water; 2 to 5 liter / minute; water temperature: 10?
The operating environment: temperature 2 - 40? The working current: test current is 29mA. The ammeter indicating current must be connected to the negative electrode of the laser tube. When it is working under over - high current for long term, the negative pole will appear light yellow, and the life span will be reduced rapidly. To protect dust from going into the insulation sheath, please wrap it with plastic film.
Do not clean the exterior surface of the output widow mirror with tools such as tampon; otherwise the output power will be seriously affected. The followings are the designated methods to clean up pollution in the exterior surface of window mirror: 1 When the mirror is polluted, do not turn on the laser. 2 Blow the mirror surface sideway with air blower.
3 Spray the pure alcohol on the mirror surface with sprayer. 4 Turn on the laser after the alcohol gets fully volatilized. 5 If the methods above don't work effectively, it is necessary to ask for the professional to use tampon with alcohol to clean the mirror surface from middle to edge.
The best solution is to prevent the window from being polluted. It is forbidden to clean the mirror with acetone. The screw in the front and back ends of the laser tube is not allowed to be moved, otherwise the out power will be declined and even the tube may be scrapped. Put the acryl 300mm far away from output mirror, when testing the laser spot. The laser beam is invisible light.
Please wear protective glasses when debugging the laser. The positive pole is in high voltage. Pay attention to the security marks. Pour out cooling fluid in the event of storage and transportation, and cover the output terminal with a dust - proof plastic bag.The storage environment is 2 - 40? And the requested humidity is 10 - 60%. Pack the laser as in the original way. Important notes: it is requested to cement the sponge together with laser tube to prevent the tube vertically sliding during transportation.
The sponge in the side of output mirror must be 70mm beyond it, and the sponge in the side of reflecting mirror must be 50mm wider. The company shall not take the responsibility from the 8th day. The replaced laser tube enjoys the quality guarantee as the new one from the manufacturing date. The company is not responsible for any damage and change of laser structures. From the 180th to the 300th days after manufactured, if the user follows the instructions and the power output happens to be lower than 85% of the rated power output, the company shall provide either repair or replace the laser tube with our special tube (depending on specific case) for free.
All our products directly from factory, no agents, no middleman, which allow to have competitive pricing. Great discounts available for order over certain amount. Customers can choose to join our membership program for reward points or discounts and we offer VIP sales or events for our members. The item "Reci W2 100W CO2 Laser Tube For Laser Cutting & Engraver Machine" is in sale since Tuesday, January 10, 2017.
This item is in the category "Business & Industrial\Healthcare, Lab & Dental\Other Healthcare, Lab & Dental". The seller is "lasercheap" and is located in CN.This item can be shipped worldwide.